Commercial roof installation in Houston, TX

Step 7 Flashing and details that stop leaks

Most leaks happen at details, not the field of the roof. We build strong terminations at parapet walls and copings, pitch pans and pipe boots, curbs around RTUs, fans, and vents, expansion joints, and drains, scuppers, and gutters. We seal penetrations, use prefabricated corners where possible, and reinforce stress points.

Step 8 Quality checks and final walk

We inspect seams, flashings, drains, and edges. A punch list is handled before we call it done. We provide completion photos and maintenance tips. You get a clean site and a watertight roof.

Roof systems that work in Houston

You do not need every option under the sun. You need the right one for your building, budget, and use.

TPO single ply membranes

TPO is popular across Houston for a reason. It reflects heat, resists algae, and welds into a strong, continuous sheet. In many cases it offers a good balance of performance and cost.

• Best fits Retail centers, warehouses, offices with low slope roofs. Owners who value energy savings from a white surface. Buildings with moderate foot traffic.
• Keep in mind Add walkway pads near service paths. Grease from kitchen vents needs proper containment. Use a cover board for hail and traffic resistance.

PVC single ply membranes

PVC resists chemicals and grease better than many other membranes. Welded seams are strong and the surface stays bright.

• Best fits Restaurants, food processing, labs, and facilities with chemical exposure. Flat roofs with frequent equipment service traffic.
• Keep in mind Use thicker membranes in high traffic areas. Confirm compatibility with rooftop products.

Modified bitumen and BUR

These multi layer systems have been used across Houston for decades. Modified bitumen and built-up roofs handle heavy traffic and can be repaired easily.

• Best fits Schools and facilities with daily rooftop access. Owners who want a tough surface under frequent foot traffic.
• Keep in mind Reflective coatings can reduce heat gain. Install methods vary. Cold process often helps with odor control near occupied areas.

Standing seam metal

Metal roofing offers long service life on sloped structures and gives a clean architectural look. Panels shed rain quickly and can pair with underlayment systems for added protection. Learn about standing seam systems that perform in wind zones.

• Best fits Office entries, retail canopies, and buildings with visible sloped roofs. Industrial structures with longer spans.
• Keep in mind Pay attention to panel gauge and clip spacing for wind zones. Sealant and closure details at ridges and eaves matter.

Roof coatings for restorations

If your current roof is mostly dry and the deck is sound, a coating system may extend life. We prep and repair, then apply silicone or acrylic coatings that can reflect heat and seal minor cracks.

• Best fits Roofs with limited wet areas. Owners looking to buy time between full replacements.
• Keep in mind Not a fix for major ponding or deep substrate damage. Surface prep is everything.

Drains, scuppers, and details that actually work

Houston rain can go from sprinkles to a wall of water in minutes. That is fine if the roof drains fast. It is a leak festival if it does not.

• Internal drains We set new drains or retrofit inserts, bolt them tight, and tie membranes directly into the bowl.
• Scuppers and overflow We size and place openings so water can escape even if a main drain clogs.
• Gutters and downspouts We pitch them correctly and fasten to handle the load. See our gutter installation service for related work.
• Tapered insulation We build channels that move water to drains.
• Parapet and coping We lock in edge metal with cleats and correct fastener spacing to handle wind.

Do your drains clog every fall? Ask about strainers and maintenance tips during your estimate.

Energy code and permitting in Houston

We work with City of Houston permitting and follow current energy code in climate zone 2. Here is what that means for your project.

• Insulation Many projects target R 25 c.i. or higher with polyiso boards. We confirm the requirement for your specific building type.
• Cool roofs White single plies help with reflectance and aging. We can provide data sheets for reflectivity and emissivity.
• Fire rating We match assemblies to Class A where required and provide documentation.
• Wind uplift We follow fastener patterns and edge metal requirements that meet ASCE 7 and tested approvals.
• Slope New roofs need positive slope. We incorporate tapered layouts to meet code and improve drainage.

Permitting through City of Houston is handled by our office. We schedule inspections and provide any needed updates.

Scheduling, safety, and jobsite logistics

Your crew still needs to work, serve customers, or ship product while the roof goes on. Our plan keeps your day moving.

• Work hours We can schedule early mornings, evenings, or weekends to reduce disruptions.
• Safety Every project has a site specific safety plan, fall protection, and controlled access. Our crews are insured and trained.
• Crane days We coordinate crane lifts for material, set street permits when required, and keep traffic moving.
• Protection We cover landscaping, protect concrete, and guard HVAC intakes so dust and odor do not bother staff or guests.
• Noise and odor Some systems are quieter and low odor. We pick methods that fit sensitive spaces like clinics and schools.
• Clean up Daily cleanup keeps the site neat. We use magnets to sweep for fasteners and debris.

Have a tenant with a grand opening or a shipment deadline? Tell us early so we can plan around it.

What it costs to reroof in Houston

Every roof is different, but ballpark pricing helps planning. These ranges include materials and labor for typical conditions. Tear-off, wet insulation replacement, complex flashing, and crane costs can move numbers up or down.

• TPO 60 mil roughly 4 to 8 dollars per square foot
• PVC 60 mil roughly 6 to 10 dollars per square foot
• Modified bitumen roughly 5 to 9 dollars per square foot
• Built-up with cap sheet roughly 6 to 10 dollars per square foot
• Standing seam metal roughly 9 to 16 dollars per square foot